INSTALLATION PROCESS FOR GLASS ALUMINUM DOORS

INSTALLATION PROCESS FOR GLASS ALUMINUM DOORS
Surveying the installation location of aluminum and glass doors This is the first thing to do when you want to construct and install aluminum and glass doors. Choosing the location will directly affect the construction design and space structure. The installation location of aluminum and glass doors plays an important role in homeowners' life. Therefore, surveying where to install the door is extremely important. In addition, can you learn more about the site conditions, the size of the waiting box, the time to put the door in and install it? Does surveying the installation of glass doors affect other buildings?

The preparation and installation of aluminum and glass doors
>>>>> GUIDE TO INSTALLING THE ALUMINUM WINDOWS

 Thoughtful preparation helps the previous person to be more active in their work Sorting aluminum and glass doors to be installed according to the construction plan. These are: installation location, degree of difficulty, construction sequence. Prepare complete and accurate supplies. Prepare all relevant tools, equipment, ... needed. Prepare your transportation. See also: Learn Xingfa 4-Wing Aluminum Door System

Transporting aluminum and glass doors to construction sites
It is recommended to install all the glass in the door frame to avoid the impact of breaking the glass. Do not let the aluminum face rub against hard objects such as iron or sharp objects. Also do not smash the corner of the aluminum door frame to the floor. When carrying the aluminum and glass doors down the plane, pay attention to put the door in a lying position. Minimize placing vertical and vertical.

Position the outside frame when installing the aluminum and glass doors
Analyze and calibrate the position to be installed. Position the enclosure so that the position is very standard and true to the original design. Buffer, ...

Positioning the wing frame
The door frame positioning should be correct in the direction of the door operation. In this stage, it is necessary to follow the correct structure to operate smoothly and accurately.

Editing and finishing
This is the completion stage. Need to adjust the hinge, movement bar, slide wheel, .. Ensure the door when closed and opened can operate smoothly and effectively. Check and complete the installation parts. See also: Why coffee brown Xingfa Aluminum is popular

Advantages when installing aluminum and glass doors

High aesthetics.
Aluminum and glass doors are considered to be a popular and widely used material

Light load.
The material of the aluminum and glass doors is made of aluminum and glass, so it is quite light in weight. The door is designed with hollow compartments, along with the design of reinforcement lifts. Therefore, the use of aluminum and glass doors will reduce the load compared to the use of other materials.

Sound and heat insulation effectively
The aluminum bar has a hollow cavity structure with ribbed ribs. From there, helping aluminum and glass doors have sound insulation, effective insulation and good bearing.

Convenient, easy to clean
Today, aluminum and glass doors are gradually replacing traditional doors such as wooden doors and plastic doors. Become a trend of many families. With many outstanding advantages, the aluminum and glass doors bring the modernity. Knowing the installation process will make it easy to install the glass. Technical standards After completing the installation of aluminum and glass doors, you need to check that they have conformed with the following technical standards. + For the horizontal edge, it must be balanced, perpendicular to the vertical frame. + For sliding doors, to pay attention to the lower rails must be straight. Acceptable error is 0 ~ 0.5 °. Applicable for all door types and 0 ° ~ 1 ° applied to fixed glass walls. + The gap to be pumped must be even and balanced. The bottom edge of the frame must have a gap of at least 3 mm to inject foam glue. + The covers to seal the screw holes need to be fully installed, the glue pump for the screw caps installed on the bottom edge on the door frame. + The standard of installation holes is to use mounting screws directly by hand to the frame. The distance from the frame corners or from the connection points to the drilling position is about 100 ~ 150 mm. The installation screws shall not be placed in a position between the end of the frame and the connection connector. See also: High-class Aluminum Door in European Architecture

PROCEDURE OF SILICON PUMP

 Step 1: Clean the dirt on the glass surface thoroughly. Ensuring the best adhesion condition of silicone adhesive is that the glass surface is dry.

Step 2: Attach silicone glue to the dedicated glue gun. Cut the tip of the injection nozzle to suit the size of the firing line. Open the glue gun and move the gun evenly at an angle of about 45 degrees. Slowly shoot an adequate amount of adhesive onto the aluminum and glass surface. Make sure the glue is enough to seal gaps without getting too much smudged.

Step 3: Prune off the excess silicon glue with a special silicone knife. Help the sugar glue neat, more aesthetic.

Step 4: Wait until the silicone glue dries and hardens before using the product. Above are some suggestions from Grando to better understand the process of assembling and gluing aluminum and glass doors. Contact for support: 0917.522.222

See also: Things You Should Know About Thanh Dinh Aluminum