CAUSES AND HOW TO HANDLING WATER SENSOR IN GLASS ALUMINUM DOORS

CAUSES AND HOW TO HANDLING WATER SENSOR IN GLASS ALUMINUM DOORS
When using aluminum and glass doors, the door exposed to the rain shows a common state of water permeability. Water penetrates between the wall and the aluminum frame. Water flows from the top glass frame down the vertical aluminum bars. This is common in common glass aluminum doors. If dealing with this phenomenon from the outset, then 99% water intake will be limited.

1. The phenomenon of waterproof aluminum and glass doors:
Window water:
When water is absorbed inside the window, stains will appear around the wall. Water flows through the slots that are in contact with the window frames. Water seeps out at the joints and bad silicone glue. Multiple states can flow into a stream, causing damage to walls, floors and household items. Therefore, it is easy to confuse the user.

Water absorbent door:
Similar to windows, but other than that, doors that could be seen seeping through the floor appeared floating from the doorway. See also: Overview of Grando - Xingfa aluminum system. How many types of Xingfa Aluminum?

2. Some common cases:

• The water penetration between the wall and the frame can be due to a baffle, but very little penetration.
• Water flows from the glass frame into the house through the right angle joints (due to poor installation techniques), leading to penetration through the door corner.
• The position under the aluminum frame has a water trough, if the worker outside the glue pump does not leave holes for drainage, 100% of the water will be spilled into the house.
• Quality of materials for the door: The aluminum system is not optimal and waterproof. The glue quality is not good, the aluminum system is not intelligent, the accessories are not synchronized.
• Door processing is not good, creating openings for water to penetrate, carelessly construction, do not pump glue well, do not handle high-risk areas well.
• Do paint before application. This we need to calculate, if the wall has not been painted, then to finish the painting of aluminum and glass, avoid worrying about leakage later.If you miss the paint before making the door, you need to use sandpaper to scrape off the paint to create adhesion layer for silicone glue.
• In addition, there are many other causes that below we will

3. The waterproofing treatment method for aluminum and glass doors
Depending on the cause, we have different waterproof treatments for windows and doors:

Door machining technique is not good.

• This user cannot handle, only the manufacturer can handle it. We should choose a reputable aluminum supplier and ensure quality

Aluminum door system is less intelligent.

• Do not be cheap but choose poor quality aluminum. Look for a reputable aluminum dealer like Grando. Grando aluminum has outstanding waterproofing, soundproofing and heat insulation.

The glue used is not good or the glue is pumped incorrectly.

• Grando's advice to remember to buy genuine is to avoid poor quality knockoffs.

Reckless construction, poor technique.

• You also have no control, warranty control and good construction supervision.

Do painting before construction of the door.

• This you should also consider, if you have not painted the wall, then you have to finish painting with aluminum and glass. If you miss painting the wall before making the door, you need to use sandpaper or scrape to scrape off the paint to create adhesion to Silicon glue.

Do not calculate when grouting.

• Should use a ledge (sump) with the foot of the door.

Because the door is open inward.

• This is difficult, design error. The door opens to the inside, leading to rain water to always pull inside, you should replace the new door.

Due to heavy rain, the amount of water splashed into the house a lot.

• This is also possible, but probably a little, with some door systems even high level of water resistance of the door has a certain limit. By using smart aluminum system such as Roto-i aluminum sliding door that can be closed with perfect waterproof 2-way

Because the old door is broken.

• This should be fixed or replaced as soon as possible. Safety first, protect ourselves and our loved ones with smart door systems.

Temporary measures in case of rain:

• Use everything you can to seal leaks, watch regularly if wooden floors or electrical appliances are nearby.

4. How to treat the water entry causes of aluminum and glass doors
Error of poor erection processing:
+ You should choose a reputable unit with a team of construction workers and factories. + Units with modern equipment, technical standards must be clearly consulted.

The aluminum system is not smart and of poor quality:
You choose high quality aluminum Xingfa or higher. Xingfa Aluminum is imported and comes with genuine Grando accessories.

Careless construction and poor workmanship:
+ Control right from the beginning, monitor quality right before construction. + Choose high-grade aluminum system, soundproof, heatproof, withstand the bad effects of the external environment. + Use genuine, synchronized accessories. + Control well the selection of prestigious units, construction and installation. At the same time good supervision at construction. Above are the sharing of causes and treatment to avoid water absorbent in aluminum and glass doors.

For more information, please contact hotline 091.752.2222 or refer to website grando.vn

See also: Things you need to know about aluminum profiles